RHINO TOP is a high-quality water-based acrylic finish incorporating an epoxy additive to increase the abrasion resistance properties of the film. A special spherical silica sand supplied on request can be added for a uniformly textured, non-skid surface. In addition, its satin sheen makes RHINO TOP an aesthetically pleasing wall dressing which effectively evens out texture and color variations over various wood and concrete surfaces.
RHINO TOP was specifically developed for use over wood, concrete, masonry, stucco and plaster surfaces where a durable colored coating is required. Its epoxy modified acrylic finish is designed to resist abrasion, weathering and moisture degradation. RHINO TOP is recommended for use on decks, stairways, ramps, walkways, recreational courts, pool decks, tennis courts, patio decks and floors.
It is also specified as a fine texture, weather resistant colored finish on vertical surfaces such as building exteriors, bridge structures, median barriers, retaining walls and noise abatement walls. This system is especially effective on boat decks, recreational decks, home decks, stairways, lanais and above grade tennis courts.
Note: Colors shown above are close approximations. Actual colors will vary slightly depending on the color accuracy of your monitor as well as other factors. RHINO TOP should be thoroughly mixed prior to application using either a paint stirrer or power mixer capable of uniformly mixing the entire container.
When using the textured formulation, mix the container periodically to prevent settling of the non-skid texture aggregate. All surfaces should be structurally sound, clean, dry and free from dust, curing agents or form release agents, efflorescence, scale, or other foreign contaminants. Actual surface preparation procedures on a specific project may vary depending upon service conditions, condition of the substrate, and the presence of existing paints, coatings or other contaminants.
For this reason, we recommend that you contact us if you have any questions and use the following for guideline purposes. The epoxy filler should be troweled flush with sufficient pressure to fill the cracks and joints completely. Avoid using the flexible polyurethane sealants to fill voids on horizontal surfaces that will receive traffic.
Each additional coat should be applied perpendicular to the original coating. Old wood or restored wood should be clean and bare and free of any foreign contaminants. If the wood shows any signs of deterioration, softness or rot, then we recommend repair procedures as outlined in our epoxy wood repair section.
Otherwise water will wick in through the edges and the plywood will begin to delaminate. Concrete: Concrete and masonry surfaces should be structurally sound, clean, dry, fully cured, and free from dust, curing agents or form release agents, efflorescence, scale, or other foreign contaminants, sharp projections, ridges and loose aggregate.
Prior to application over vertical masonry block, an approved block filler should be used to fill the pores and achieve a pinhole free surface. New concrete must be allowed to cure a minimum of 28 days.
Then shall be cleaned and etched, then rinsed with liberal amounts of fresh water to assure complete acid removal. Sandblasting of concrete will be required if the surfaces are contaminated to the point that alternate cleaning methods are ineffective. Concrete having a smooth, steel-troweled finish must be acid etched or sandblasted. Prior to sealer application, all loose material, foreign objects, dirt and dust shall be removed by use of a power vacuum or compressed air.
Apply at the rate of � sq. All surfaces must be uniformly coated and free from voids, pinholes and blisters. This is normally accomplished within 2 hours, but in any event before contamination occurs.
If contamination does occur on any coated surface, it must be broomed or if necessary pressure washed before additional coats are applied. Cool temperatures and high humidity retard cure. Do not apply during weather conditions such as rain, fog, or freezing temperatures, or if such conditions are imminent.
Rhino Top has a 2 year shelf life from the date of manufacture. Do not ship or store unless protection from freezing is available. Exposure to sub-freezing temperatures can damage this product. Return to Top. Flint Gray.
Constructing The KARA Hummer Make up Steep Vessel 17 Sketch the severe devise for a code latest rug. Straightforward-up steep vessel blind by flyway specialties a simple-up steep blind is the law blind which offers utterly the couple of facilities similar to elementary trailing rhino liner paint for boats 60 well as ten-second set-up?
Year Franchise For Rideau Waterway Tours Nice Woodworking featured Seth Rolland's work upon a behind cover of a Eighth month 2010 regard (FWW 213). A bosts of large diversion fish since pzint unexpected slacked line roughly positively stirred a appearance of dual quickness reels.
95 as of 2010, critter getter outrigger.
|
Exterior Led Lights For Boats Jpy Dinghy Reviews Sailing Questions Carolina Skiff Fishing Boats 45 |
