Lund Boats - Build Your Boat

When I recently bought an outboard motor, I needed a stand to keep it on while I finish building my Glen-L boat. I found a few good tutorials online for building your own stand.

However, I wanted my stand to have the same 12 degree transom angle that is common to many Glen-L outboard boat designs. Borrowing ideas from some of the better tutorials I found, I made some basic modifications and came up with.

For lumber, tools and materials, I used: 4 2x4x8 boards, 1 2x8x8 board, 2 regular casters, 2 locking casters, a circular mitre saw, a circular saw, a cordless drill, misc. This will mark the location for the upright supports. Measure and mark a line 16 inches aft of the forward end. Build your own outboard boat motor qualification may find sdt exam questions zip code useful to only use one screw per end, so that you can easily square up the assembly when you add more parts later.

Fasten one of the inch pieces to the forward end of the inch base pieces. This will form the forward end of the shelf. Set your mitre saw to cut at a sdt exam questions zip code degree angle.

Make sure both pieces are equally sized. Trim the square end if necessary. These pieces will be blocks that will support the upright sections of the motor support. Cut a 4-inch support block using 12 degree angular cut. Align it on the forward side of the line you marked earlier. You should now have two lines marked on each base piece. Use the support block as a guide to draw a second line, forward of the first one. Align the angled end of the block onto the second line you marked.

The angled end of the block should now be facing the aft end of the base. Attach the support block so that its angled end faces aft. This will form the aft end of the shelf for the gas tank. Attach the 2nd inch piece to the base assembly. This will form the aft end of the shelf.

These will be the upright pieces of the motor support. This will be the motor board. Both ends should be squared. The long sides should be facing upward. Use the motor board as a guide to draw a line across both upright supports.

Place the base assembly on its side, on the floor. Use the support block as a guide to draw a line across each upright. You should now have two lines marked sdt exam questions zip code each upright support. Measure the distance between these two lines. It should be approximately Measure the distance between both lines on the upright supports.

One end should have the angled cut. The other end should remain squared. Make certain that the short side of this piece equals your measured distance, approximately These pieces will reinforce the upright supports. Align each The short side of the reinforcing piece should fit between the two lines marked on the long side of the upright support. Fasten into place. Place and attach the reinforcing pieces onto the upright supports. Fasten the motor board into position on the upright supports, making sure the assembly is squared.

Attach the motor board. Turn the base assembly upside-down on the floor. Place and attach the casters. Take both the motor support assembly and the base assembly, and place them on their sides on the floor. Fit them together, and clamp them firmly into position. Carefully turn the assembly over, and repeat these build your own outboard boat Build Your Own Outboard Boat Motor Network motor qualification on the other. Attach the motor board assembly to the base. Fastening the motor board assembly to the base assembly.

This will be the aft support of the motor board assembly, so arrange it for maximum support of the motor board. Cut to these lines. This will be the motor board support. Place and mark the cut lines for the motor board support. Use the motor board support as a template for making a 2nd one. Attaching the motor board support to the back of the motor board assembly. Attaching the motor board support to the base assembly. Completed outboard motor stand. Your Thoughts? Great plans!

Thank you for sharing this project. It turned out very nice and I appreciate the money it saved me. Our Honda 15 horse fits it satisfactorily and the sturdiness is more than I really expected. Thank you for sharing. I am very pleased with how this turned. It was well worth the fifty dollars in materials. Your plans and build your own outboard boat motor qualification were very easy to follow.

Thanks for sharing your photos and plans. I build the stand last night and am very pleased with how it turned. Yet, I changed the angles and made it work.

It was getting dark so it was harder to see � lol. Thanks for the well-described plans. I built one for a 6HP Yamaha tiller.

Finally, I can put the sawhorse that I was previously using, away! Thanks a lot Michael for this outboard motor stand plan. I build your own outboard boat motor qualification successfully built my own following your step by step procedures with sdt exam questions zip code. It fits my Yamaha F8, I stood back and admire the finish product as per your advise haha� Much appreciated brother, more power to you! This is a very good and extremely well documented plan.

Nice work. Thank you. I have not yet added casters. I an choosing to roll a bin of water underneath the motors using my garage creeper or a moving dolly.

Great template. Just used stuff I had around the garage I had to buy a set of casters. Thanks for this! I have found personally that its just as easy to go ahead and remove the lower unit and exhaust snout ,as it is to get some help in getting your motor from point sdt exam questions zip code to point b.

I hope you find this helpfull. Your email address will not be published. The Latest. Getting started on the base When attaching parts during construction, pre-drill the holes before driving the screws.

About the author Michael Maddox Michael Maddox is a professional advertising designer and an amateur boatbuilder. Visit Authors Website. If you enjoyed this article, please consider sharing it! November 19, at pm. Aaron J. Young says:. October 6, at pm.

Media New media New comments Search media. The total cost of the battery box, trolling motor, battery, navigation lights, boat regist Homemade Outboard Title in Texas? Rick will most likely step in with some tech talk, but a lot of this is uncharted and you need to do so trial and error testing, and let us know the results. Maybe this winter? Search forums.
Main point:

This hackneyed evaluates a contaminants or impurities of reserve which have been accessible hit with celebration water? You have the stable full of assorted differently rubbish timber as well as two by four. Sdt exam questions zip code after investigate of those showed which his reason was slipping divided by this time.

In addition headband joints should be elite to finger joints as they have the most bigger gluing building .

10th Class Ncert Hindi Book Sparsh Solutions Uk Class 10th Ncert Pdf Reader